![]() I’m going to return the tunable bulbs as a result - they are not worth my time. This is doubly painful because once I finally get a preset dialed in, I can’t copy it to other bulbs. However, when I then go to set up presets, I’m forced to set white balance and brightness blindly - there are only sliders, with no Kelvin and % numbers. I like how I can see the Kelvin temp when I’m setting white balance, as well as the brightness %s. One should be able to copy presets from one device to others - it’s ridiculous to have to set these up from scratch with each device. The bulbs are great, but the software needs some work - and is frustrating to use in the meantime. Preset and schedule functionality not up to parįirst I purchased two Kasa dimmable smart bulbs, and then I purchased three tunable ones so I could change the white balance. I have a neighbor that cant figure out how to turn off her outside lights and this would be great for her, but I still think the idea of this light is pretty cool. I have used it here and there and think it’s a great idea. I also own one of their light bulbs, but havent found a great use for it yet. I have now bought more of these smart plugins and use them to turn off other tvs and xboxs on power strips when my kids arent listening and have a lamp in the living room I have set on a schedule to turn on before I get to the ground floor so I dont trip on anything on the floor the kids may have left in the middle of the night when they should have been sleeping. I also have a strip for my xbox, tv, and headset charger. It saves electricity instead of having the strip plugged in all the time. This power strip only charges my phone, watch and iPad most nights, but I have also had my xbox controllers charger and sometimes other things connected to the strip. I started with the little 2 pack starter kit and used this with my power strip to turn it on at night and off in the morning when I am not here. Or this can be attached to a red light so when we come into the office we can see the network went down over the weekend check out everything to make sure all systems operational. The switch can detect the failed network and turn it back on again. This way if someone accidentally shuts off the router or modem. I.e if the network goes down turn this switch on and when the network comes up leave it on or have a feature to turn it off. Of course we need to make note of the time it is and make sure the turn on schedule is scheduled first so we don’t accidentally lock ourselves out of the switch.Īnother nice feature would be to have a failsafe toggle. As it stands now we gotta go in and schedule a turn off and schedule a turn on one minute later. It would be nice if we could open the switch and have a reboot button that would tell the switch to turn off for five seconds and turn on again. We can’t “turn off” this device cause then we won’t be able to “turn on” after since the network would be down. Sometimes when our on-site Internet gets rather flaky we need to reboot the modem. We can turn on and off pumps as needed without needing to go to the site.įunctionality is simple but it works! Only think missing is a “reboot” function. If I remove the XG from my network and plug in my D-Link DIR850L Router, I can access the smart switches remotely with no problem.We use this app to control our devices remotely. I can see traffic going out as "Allowed" in logging and all looks fine from the XG side, but the switches are still inaccessible. No IPS, Traffic Shaping, Web Policy, App Control No Scan HTTP, HTTPS, Block Google, Scan FTP Source Networks and devices: "My two devices" So I reserved their IP's and created two new firewall rule as follows: TP-Link doesn't give much assistance with their devices but I found a website which says that the plugs use Ports: According to TP-Link this message indicates that remote access is not enabled on the plug but when I look into the settings it is. If I connect to the local network, the plug displays "Local Only". I have noticed that when trying to control remotely, they grey out on either iOS or Android. I run TP-Link Kasa Smart Plugs in my house.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |